100% Awesome DIY Woven Headboard

DIYWovenHeadboard00001
DIY Woven Headboard

Do you want to spice up the look of your bedroom? This woven headboard is a simple project that could be completed easily over a weekend.

This DIY woven headboard is rustic and simple — if you are into this kind of style, then this could be the perfect woven headboard for you. But if not, you could also stain or paint it any colour you’d like!

Click on any image to start the lightbox display. Use your Esc key to close the lightbox.

Materials:

  • 1 piece of 1/4″thick 4′ x 8′ hardwood Birch Plywood
  • 2 pieces of 1″ thick 2″ x 6′ Pine Wood
  • Wood Stain – optional
  • Clear Finish
  • #8 2″ Wood Screws
  • Wood Glue
  • Eye-hooks
  • Picture-hanging Wire
  • Heavy Things (to serve as weights)
  • Padding Material

Tools:

  • Measuring Tape
  • Saw
  • Paintbrush
  • Wood Clamps

Steps to make your own woven headboard:

Cut plywood sheets and timber into these pieces…

  1. Cut three 10″ x 8′ strips from the plywood
  2. Cut each strip into 2 pieces, one 63″, and one 33″
  3. Trim 2″ from one of the 63″ strips; save the cutoff for later
  4. From the leftover plywood, cut a piece 10 x 35″
  5. From that piece, trim a 2 x 10″ piece
  6. Then cut the resulting larger piece into two 5 x 33″ pieces resulting Plywood Pieces:
    2 – 10 x 63″
    1 – 8 x 63″
    1 – 2 x 63″
    2 – 5 x 33″
    3 – 10 x 33″
    1 – 2 x 10″
  7. Cut the 2 x 63″ & 2 x 10″ strips into 5″-ish pieces (you’ll need 10 of them)
  8. Chop the 1″ x 2″ x 6″ wood into:2 – 2 x 53″
    2 – 2 x 23″
DIYWovenHeadboard00002

Put the two 10″ long strips on a flat surface, grain-side up. Place a 10″ short strip at each end and centre the third.

Use chalk or a pencil to mark the edges of the cross-strips, then remove the short strips. Apply glue, then replace the pieces. Do the end pieces first, making sure that the edges are flush; then re-place the centrepiece.

At each intersection of your DIY woven headboard, place something heavy to push the strips together. Use enough weight to ensure that you get a solid connection. If you have sawhorses, or enough milk crates, etc., you should use those & clamp the intersections instead. You’ll get better joins that way.

Let that dry for a couple of hours before proceeding.

DIYWovenHeadboard00003

Flip the assembled piece over. Center a 5 x 33″ strip between the middle cross strip and either end cross strip, grain side down. Mark the edges, glue, and weight.

Let the glue dry for at least an hour before moving on.

DIYWovenHeadboard00004

Flip the assembled piece back over.

Take the remaining long strip and weave it through the cross pieces, over and under. You want it on top of the crosspiece at each end. (Look at the pic, it’s easier to understand than a written description.)

DIYWovenHeadboard00005

Apply glue to the intersection at each end, then clamp. Let this dry for at least a couple of hours (but go ahead and start the next step whenever, as you’ll be leaving this assembled piece for now).

DIYWovenHeadboard00006

Take your frame pieces and make a, well, frame with them. Stand them on the edge and glue then screw them together with butt joints.

Once the headboard proper’s glue has dried, flip it over. Place the frame on it and get it centred, then trace its outline onto the plywood.

Glue the 5″ -ish pieces to the back of the plywood to make a level surface to attach the frame. You’ll need to stack 2 on the ends. Let that dry for at least an hour.

DIYWovenHeadboard00007

Apply glue to the top of each 5″-ish piece, as well as the backs of the strips at the same level, then re-place and clamp the frame. Let that dry for a few hours.

Drill pilot holes into the frame, then use screws to further secure the 2 components together. (This might be overkill, but this is what’s going to hold the whole thing up, so you want to make sure it stays together.)

Once the woven headboard is done, we move on to finishing!

DIYWovenHeadboard00008

If you want to go with the natural colour of wood, skip this step.

Sand the entire piece with 120, then 220 grit sandpaper. Be careful not to sand through the top layer of the plywood, or to crack the edges.

I stained using a grey “sunbleached” shade, then sanded that back a good deal with the 220, just to make the grain pop.

DIYWovenHeadboard00009

Apply your preferred clear coat to your woven headboard. I went with amber shellac, semi-gloss, entirely because I had a can leftover from another project.

Apply a coat, sand it smooth, apply a coat, and repeat as needed. Check your can of finish for instructions, I’m not a varnish prophet. 🙂

DIYWovenHeadboard00010

If desired, add your padding material to the exposed edge of the frame.

Install a picture-hanging wire on the frame; put the eye hooks into the inside of the frame, not the outer edge.

And that’s that. To hang it, insert a screw or picture-hanging hook in your wall (make sure to anchor it if you don’t have a convenient stud), and hang ‘er up.

Do you think you could still improve this DIY woven headboard? Or is it perfect as it is? 🙂

Thanks to jmacfarlane for this great project.

YOU MIGHT ALSO LIKE

|

Search All Projects:

|

Our Deal For Today!

Your details will never be shared with any third party. Unsubscribe at any time with a single click.

The posts on this site sometimes contain an affiliate link or links to Amazon or other marketplaces. An affiliate link means that this business may earn advertising or referral fees if you make a purchase through those links.