How To Build A Rocking Chair With Crib

DIYCrib01

It’s around 3 or 4 a.m. and you’ve finally gotten the baby back to sleep. Gently, ever so gently, you place him back in the crib but his eyes are open before you’ve even had a chance to head back to bed! This is an episode every parent knows all too well. This rocking chair with crib is the perfect solution!

This project shows you the steps on how to build a rocking chair with a crib attached to it. It’s very easy to build if you have basic carpentry skills and the required materials, hardware, and tools.

How to build a rocking chair crib

This will make life easier for all the bleary-eyed parents. And when the kids outgrow the crib it makes a great yarn storage and knitting chair. Before starting the project find a mattress and cushion of your choice and adjust the plans dimension accordingly.

Materials:

  • Pine Board Sheets
  • Thin Plywood – for seating and crib mattress
  • Wood Glue
  • Super Glue
  • Screws (not longer than the thickness of the wood and 4 pieces slightly longer)
  • 4 pieces Metal Corner Brackets
  • Varnish (or Paint)
  • Fabric (50×50 cm)
  • Foam Mattress (42×44 cm)
  • Weights (or any heavy material for gluing wood pieces together)

Tools:

  • Table Saw
  • Jigsaw
  • Drill
  • Sander (with soft and rough sanding paper)
  • Brush
  • Staple Gun

Steps:

Before starting the project, check out the crib mattress that you will be using first for accurate measurements. The dimensions in this photo makes a bigger than usual crib. So basing on the mattress that you find, just adjust the measurements accordingly. 🙂

DIYCrib02

What’s nice about this project is that the cutting list is pretty easy to follow. The only detail we think we have to discuss in particular are the one for the sides. To create the curve at the bottom, use a long strip of scrap wood or string (around 125cm), and anchor it temporarily to the center of the top edge of your board. Attach a pencil on the other end of your string, and trace a curve on your board as the pencil pivots around the anchor point.

DIYCrib04

Then simply follow the other measurements indicated in the sketch above to create the shape of the sides. Once everything is cut, sand all pieces, especially the edges.

DIYCrib05

Next, make a line under the center line of the side boards, with a distance as that of the thickness of your base board. This is where you will install the corner braces, as shown in the picture below.

DIYCrib06

Flip the side boards over so that the curved edge is on top. Find any object that can hold your base board flat at 20 cm height. Apply wood glue to the shorter edge of the base board and attach it to the side board like in the picture. Once it has dried, drill screws through the bracket and base.

DIYCrib07

Do the same for the other side. Once the wood glue is dry, ensure the stability of these three pieces by flipping it over to its right position and sitting on it.

DIYCrib08

If your three main pieces are secured, you can then proceed to attaching the wings. In this example, tapes were used to hold the wings in place for 24 hours while waiting for the wood glue to dry. You can use clamps if you have some.

DIYCrib09

Then glue the shorter sides of the crib. You can use weights or books to press the pieces together as the glue dries.

DIYCrib10 DIYCrib11

After that cut the backboard piece so that it fits perfectly between your armrests. Using leftover wood, cut 7×52.5 cm pieces and round off the outer corners. See picture below. Glue the backboard to these two pieces and leave to dry. Once it’s dry, flip the entire crib sideways and attach the backboard.

DIYCrib12

Make sure your pieces are strongly glued to each other by sitting and leaning on the chair. Then cut 5×55.5 cm armrest pieces, with round corners, from your leftovers.

DIYCrib13

This next couple of pieces are optional – if you want to be able to use the furniture without rocking. Simple cut two pieces of triangle and attach it to a strip of wood, as seen in the picture. Determine the distance by measuring them with the bottom of your rocking crib.

DIYCrib14

It should fit perfectly that you can simply slide this stopper from the side with the triangles underneath the curve.

DIYCrib15

Sand the entire furniture once more to make sure there are no rough edges and paint it to your desired finish.

DIYCrib16

For the seat, cut 3/4 plywood to 42×44 cm and round off the corners.

DIYCribSeat01

Glue the foam mattress with super glue or any glue you have to hold them together.

DIYCribSeat02

Then use staple wire to tightly cover it with your chosen fabric. The one in the picture is fake leather.

DIYCribSeat03

Secure the seat in place by screwing at the corners it from below. Therefore you have to make sure you have four screws that are long enough to go through the base board and hold the seat, but not too long that it also goes all the way through the plywood. You don’t want to get pierced by the screws as you sit! 🙂

DIYCribSeat04

Thank you vatkin for the great idea!

 

Close Menu
close-link
Close Panel